• 联系人:王经理
  • 手机:15006406386
  • 电话:0531-88271922
  • 地址:济南历城区华山工业园
    如何对电动卷帘门进行结构调试
    发布来源:http://www.jnykckm.com 发布时间:2018-11-30 15:43:28
    如何对电动卷帘门进行结构调试
    How to Debug the Structure of Electric Curtain Door
    调试是电动卷帘门安装最后的一个步骤,也是最重要的一个步骤,调试准确对以后的使用都起到了决定性的作用。
    Debugging is the last step and the most important step in the installation of electric shutter doors. The accuracy of debugging plays a decisive role in the future use.
    调试前的准备工作
    Preparations before commissioning
    1.电动门执行器已正确安装。
    1. The electric door actuator has been installed correctly.
    2.所有的螺丝,连接器和电气连接是安全的。
    2. All screws, connectors and electrical connections are safe.
    3.电气连接是正确的和正确实施接地和粘接。
    3. Electrical connection is correct and correct implementation of grounding and bonding.
    4.执行机构和阀门处于良好状态,手动自由没有卡纸。
    4. The actuators and valves are in good condition, manual free without paper jam.
    5.模拟指令,反馈是正确的。
    5. Analog instructions, feedback is correct.
    如何对电动卷帘门进行结构调试
    How to Debug the Structure of Electric Curtain Door
    2,SIPOS电动执行器调试器
    2. SIPOS Electric Actuator Debugger
    6.第一个执行机构调整的信号,根据要求比减速。
    6. The first actuator adjusts the signal to decelerate according to the requirement.
    7.相应的MCC抽屉在当地媒体上的控制面板,遥控器的按钮一次或多次,执行机构的业务模式,远程控制传输,本地参数设置和调试这三种模式之间切换。

    7. The control panel of MCC drawer on local media, the button of remote controller one or more times, the business mode of executing organization, remote control transmission, local parameter setting and debugging are switched among the three modes.

    济南电动卷帘门

    8.选择这种模式的参数设置和调试,有四个主要的菜单(语言设置,调试,观察,诊断)。语言设置:当您选择所需的语言按回车键(通常是英语),共有五种语言选择(德语,英语,法语,西班牙语,意大利语)。
    8. There are four main menus (language settings, debugging, observation, diagnosis) to select the parameter settings and debugging of this mode. Language Settings: When you select the language you need and press Enter (usually English), there are five language choices (German, English, French, Spanish, Italian).
    9.进入调试菜单,并输入四位数的PIN码(9044),更改设置并关闭了阀门相关的参数,关键参数的显示:速度,打开速度,紧急起飞的速度,紧急打开速度,封闭端位置的关断模式,关断模式,开放的终点位置,最大扭矩关系,最大开扭矩,扭矩故障重复,上升时间,直流制动,电机温度报警,电机温度保护,电机发热,调整结束的位置,记录的扭矩曲线。如果参数的变化,只要列出的参数显示按回车键进入。按箭头键来更改参数。
    9. Enter the debugging menu and input the PIN code of four digits (9044), change the setting and close the parameters related to the valve. The key parameters are displayed as follows: speed, opening speed, speed of emergency take-off, speed of emergency opening, closing mode of closing end position, closing mode, open end position, maximum torque relationship. Maximum open torque, repeated torque faults, rise time, DC braking, motor temperature alarm, motor temperature protection, motor heating, adjusting the end position, recording the torque curve. If the parameters change, just press Enter key to display the listed parameters. Press the arrow key to change the parameters.
    10.调整到最后的位置调整执行机构的行程限位。首先,设置的结束位置或关闭。是开放的,例如,根据适当的执法机构,以开放的健康运行到结束,按回车键两秒钟到达终点的位置,在屏幕上显示一个错误,然后调整电位器,允许误差为零。按适当的键两秒钟,封闭运行的执行机构的末端位置,然后按Enter。设置相应的屏幕显示比例,显示设置的结束是正确的。
    10. Adjust to the final position to adjust the travel limit of the actuator. First, set the end position or close. It is open. For example, according to the appropriate law enforcement agencies, it is open and healthy to run to the end, press the return key to reach the end point in two seconds, display an error on the screen, and then adjust the potentiometer to allow zero error. Press the appropriate key for two seconds, close the end position of the running actuator, and then press Enter. Set the appropriate screen display ratio, the end of the display settings is correct.
    调试中发现的问题
    Problems found in debugging
    循环泵出口电动门的调试,打开壳盖内的电气线路的大门,和图纸不相符,使用,导致重新对接,是一个力矩开关损坏。在涡轮的扭矩开关方面是不是也发现了控制电路的连接,防止丢失。我们依靠自己,而这些问题的认真,仔细修改的MCC要求的布局。对于机组的安全运行奠定了坚实的基础。
    The debugging of the electric door at the outlet of the circulating pump, the opening of the door of the electric circuit in the shell cover, which is not in conformity with the drawings, causes the re-docking, and is a damage of the moment switch. Whether the connection of control circuit has been found in the turbine torque switch to prevent loss. We rely on ourselves, and these issues are carefully and carefully revised for the layout of MCC requirements. It lays a solid foundation for the safe operation of the unit.
    综上所述有济南华派门业提供,想了解更多济南电动卷帘门知识,欢迎关注我们的网站:http://www.jnykckm.com谢谢支持!
    In summary, all the above-mentioned Jinan Huapai Gate Industry provides, want to know more about Jinan Electric Curtain Gate, welcome to pay attention to our website: http://www.jnykckm.com Thank you for your support!